USB charger kit production steps detailed

USB charger kit, also known as MP3MP4 charger, input AC160-240V, 50/60Hz, rated output: DC 5V

This article refers to the address: http://

250mA (label sticker is 500mA, if you want to output more current for a long time, please replace Q1 with 13003). MP3 and MP4 are popular in the country, but as a charger for daily use, it is directly connected with 220V high voltage, which has the characteristics of high failure rate and easy damage. Especially after buying those immature products, it is really hard to read. . Finally, commissioned by the school teacher, we contacted a mature mass-produced charger kit, which is now shared with the majority of electronic enthusiasts.

The following is a schematic diagram of the circuit drawn on the physical object: (There are a variety of component mounting methods on the circuit board. Please refer to the schematic and physical diagram for installation. Some component holes on the PCB should not be installed. Some components should be installed. On the component hole, please pay attention!)

Note: In order to simplify the circuit and achieve the purpose of learning, the resistor F1 of 1 ohm acts as a fuse, and the rectification is completed by a diode D1. After the power is turned on, C1 will have a DC voltage of about 300V, and the current will be supplied to the base of Q1 through R2. The emitter of Q1 has R1 current detecting resistor R1. After the base of Q1 is energized, it will pass T1 (3, 4). Producing a collector current and simultaneously generating an induced voltage on (5, 6) (1, 2) of T1, the two secondary insulated coils of the same number of turns, wherein the T1 (1, 2) output is rectified by D7 After C5 filtering, the load is supplied to the load through the USB socket; wherein T1 (5, 6) is rectified by D6, filtered by C2, and passed through IC1 (actually 4.3V voltage regulator) and Q2 to form a sampling comparison circuit to detect the output voltage level; (5, 6), C3, R4 also form a positive feedback circuit of the Q1 transistor, so that Q1 works in high-frequency oscillation, and continuously supplies power to the T1 (3, 4) switch. When the output voltage rises due to any light load or high power supply voltage, T1 (5, 6), IC1 sampling comparison leads to Q2 conduction, Q1 base current decreases, collector current decreases, and load capacity becomes smaller. As a result, the output voltage is reduced; when the output voltage is reduced, Q2 is sampled and then turned off, Q1's load capacity becomes stronger, and the output voltage rises again; this acts as an automatic voltage regulator.

Although this circuit has few components, it is also designed with overcurrent overload and short circuit protection. When the load is overloaded or short-circuited, the collector current of Q1 increases greatly, and the emitter resistance R1 of Q1 generates a higher voltage drop. The high voltage generated by this overload or short-circuit will pass through R3 to make Q2 saturate and turn on, thus let Q1 Cut off the output to prevent overload damage. Therefore, changing the size of R1 can change the load capacity. If the required output current is small, for example, only need to output 5V100MA, the resistance of R1 can be changed. Of course, if you need to output 5V500MA, you need to change R1 appropriately. Note: R1 will increase the possibility of burning Q1. If high current output is required, it is recommended to replace the high power tube in 13003 and 13007.

What is the role of C4, R5, D5? The T1 transformer is an inductive component. Q1 operates in the switching state. When Q1 is turned off, a high voltage is induced at the collector. This voltage may be as high as 1000 volts or more, which will cause breakdown of Q1. Now there is a high-speed switching transistor. D5, this voltage can charge C4, absorb this high voltage, C4 can be discharged immediately through R5 after charging, so Q1 will not be damaged by the high voltage breakdown of the collector, therefore, if these three components have switch or damage, Q1 It is very dangerous and can be damaged in minutes and seconds.

After you receive the goods, first familiarize yourself with the circuit schematic, analyze the principle, then measure the components, and then carefully assemble.